کمپرسور باد 1 سیلندرTJM

General Description: TJM Pro Series Air Compressors are rigorously tested for challenging conditions. They are engineered for overlanding adventures and to meet air supply needs. The compressor's exterior is constructed from cast and extruded aluminum, offering superior protection for its internal components. This seamless anodized exterior safeguards oversized internals, a hard-anodized cylinder bore, and a Teflon-impregnated piston seal. The unit features an advanced convection cooling system with a patent-pending design. It includes multiple tire inflation points and six auxiliary ports, alongside a pressure cut-out switch for enhanced functionality. The compressor offers five unique mounting angles for flexible installation in various vehicle locations, such as the engine bay, vehicle cab, or drawer system. It is designed for universal application across different vehicles. Technical Specifications: SKU: 013COMPVHD Brand: TJM Voltage: 12 V DC Current Draw (0 Bar / 0 PSI): 46 A Current Draw (30 PSI): 55 A Fuse Type and Rating: 2x ANS 40 A IP Rating: 54 Motor thermal cut-off: 105°C Air flow: 86 Liters per minute Duty Cycle (80 PSI, 60 minutes @ 23°C): 100% Pressure Switch Operation: Off @ 120 PSI / On @ 90 PSI Safety Relief Valve Opening Pressure: 1070 kPa / 155 PSI Hardware and Fittings: Pro Locker Solenoid / Pressure Switch ports: 4 x 'A” BSPT ports (2 each side of air tank) Tyre Inflation / Accessory ports: 5 x 'A” BSPT ports (2 each side of air tank & 1 on Top Cover) Safety Relief Valve: Factory-set 155 PSI, 'A” NPT male thread Compressor to Bracket Bolts (Included): 12 x M5 x 22 Socket Head Cap Screw (Base Bracket) Weight: 6 kg Dimensions: Specific dimensions were not found or were ambiguous in the search results. Warranty: 3 Years or 100,000 kilometers Installation Guide: The TJM Pro Series Compressor is designed for basic installation with multiple mounting options. The estimated fitting time is approximately 2 hours for horizontal or vertical configuration in an open area, and 5 hours for vertical configuration in a confined area. Before beginning the installation, ensure all instructions are read and all listed components are supplied. For warranty validity, the product must be correctly installed by suitably qualified personnel and used according to the provided instructions. Any holes drilled into the vehicle body should be treated with rust preventative paint. For cable routing, install suitable sized rubber wiring grommets to prevent cable damage. Always place the product on a soft workspace to avoid damage prior to installation. Do not mount the compressor below the vehicle's water-wading line; consult the vehicle manufacturer for this specification. Compressor surfaces, particularly the head section, can become very hot during operation, so mount the unit away from flammable materials and avoid locations where it could be accidentally touched while operating. This compressor is rated for 12 V DC systems only. To fit the TJM Airline Kit, remove one of the 1/4” BSPT plugs in the air tank using a 6 mm hex key. If necessary, the safety relief valve can be removed to create space for accessory installation. Apply sealant paste (e.g., Loctite 567) or sealant tape to one end of the threaded fitting of the accessory. Other fittings can be installed on any other spare port. If the safety relief valve was removed, re-install it to the same port after applying sealant paste or sealant tape. If using a thread sealant, allow sufficient curing time as per the manufacturer's specification. Disconnect the vehicle's starting battery before commencing installation. Find a suitable mounting location for the compressor. The unit has a built-in mounting bracket; however, vehicle-specific brackets are also available to facilitate installation. If using the built-in bracket, utilize the provided template to mark and drill holes, then secure the compressor with the supplied hardware. A hose coupling should not be installed directly onto the compressor for tire inflation; instead, use the TJM Manifold or a remote coupling setup. For manifold installation, apply thread sealant to both 1/4” fittings, then thread one into the compressor and the other into the manifold. Apply thread sealant to the threads of the hose coupling and thread it into the large port on the manifold. The manifold should be mounted no more than 22.86 cm away from the compressor. Connect the stainless-steel braided air hose to both the compressor and manifold using a 14mm wrench.